Skip to content

Flashed, shimmed and sealed with care. Free quote: (714) 868-8790

(714) 868-8790

ServicesWindow Replacement

Window Replacement in Huntington Beach

We take out failing windows and install new ones that slide easily, seal tightly and keep water out of the wall. The difference comes from the details most crews rush: measuring each opening, shimming at the right points and sealing against stucco.

Installer in a cap and tool belt fitting a new white double-hung window into a brick wall, with a ladder, bucket, caulk gun and tool bag nearby

When Replacing the Whole Window Makes Sense

Window replacement means taking out the sash and glass, and sometimes the frame, then setting a new unit in the opening. It is the right call when the problem is in the window itself. Fogged dual-pane glass means the seal between the panes has failed. Worn rollers and bent tracks on old aluminum sliders cannot be brought back to a smooth, tight close. Single-pane glass passes heat straight through.

How long a new window lasts depends less on the brand than on the installation. A frame that is out of square by a quarter inch binds and wears its weatherstripping. A sill with no slope holds water against the frame. Caulk on a dusty stucco edge lets go after a summer or two. Our crew works with those details in mind on every opening.

We are an authorized Crystal Pacific Windows installer. We are also bonded and carry $2 million in insurance coverage on every job. If a window in your home does not need replacing, we will tell you so.

What Our Window Replacement Covers

Measuring each opening
We measure width and height at three points and check both diagonals. Older stucco homes rarely have perfectly square openings, so each window is ordered to the smallest measurement, with room left for shims and sealant.
Retrofit or full-frame choice
Most stucco homes take a retrofit window with a flush fin that covers the old aluminum frame, which avoids cutting the exterior wall. When the old frame is damaged or out of square, we recommend a full-frame tear-out and explain the extra work involved.
Shimming and fastening
We shim behind the jambs at the lock and roller points, then check that the frame is plumb, level and square before we fasten it. A frame that is twisted even slightly drags on the sash and wears out the weatherstripping early.
Sealing the perimeter
Gaps get low-expansion foam, which will not bow the frame. The exterior joint gets a sealant that bonds to stucco, applied over a cleaned surface so it stays attached.
Tempered glass where code requires it
Windows close to doors, tubs and showers, or close to the floor, need safety glass. We identify those openings at the estimate and order tempered glass for them.
Cleanup and haul-away
We take the old units with us, vacuum the sills and tracks, and walk through each window with you before we leave.

Signs Your Windows Are Ready to Go

  • Cloudy glass you can't clean

    A haze between the panes means the edge seal has failed and moist air has gotten in. The insulating gas is gone, and the fogging will not clear.

  • Sliders that drag or jump the track

    Aluminum tracks pit and bend over the years, and the rollers flatten. Once the sash fights you, it no longer closes tight enough to seal.

  • Drafts and whistling on windy days

    Worn pile weatherstripping and loose glazing beads let air pass at the meeting rails. You can often feel it with the back of your hand.

  • Corrosion on frames and hardware

    Salt air pits aluminum frames and locks, especially near the coast. Chalky white corrosion around the latch usually means the lock no longer pulls the sash closed.

  • Water on the sill after rain

    Clogged weep holes or a failed exterior seal let water collect inside the frame. If it isn't dealt with, it can stain drywall and damage the framing beneath.

How a Replacement Day Runs

  1. 1

    Free in-home estimate

    We measure every opening, look at the condition of the frames and the stucco around them, and go over retrofit and full-frame options with you. There is no sales pressure and no obligation.

  2. 2

    Ordering and scheduling

    Windows are built to the exact measurements we took. Once they arrive, we schedule your install day and let you know which rooms we will be working in.

  3. 3

    Removal and prep

    We lay down drop cloths, take out the old sash, and clean the existing frame or remove it. The sill is checked for slope and rot before anything new goes in.

  4. 4

    Setting and sealing

    Each window is shimmed, squared and fastened, then foamed and sealed inside and out. We test every sash and lock and confirm the weep holes are clear.

  5. 5

    Walkthrough

    You open and lock each window with us before we sign off. The old windows and packaging leave with our crew.

Installer in a cap and tool belt lifts an old aluminum window out of a stucco wall opening, with a ladder against the eave and a new white window on the lawn

What Affects the Price

Your quote depends on how many windows you are replacing, how big they are and what we find in each opening. We list every window with its installation method on its own line, so you can see where the cost comes from. If an opening needs extra work, we show you why before it goes on the quote.

Window count and size
Larger openings need heavier glass and sturdier frames. Each added window adds labor, though setup time is shared across a full-house order.
Retrofit versus full-frame
A retrofit over the existing frame takes less labor. Full-frame removal means cutting back stucco and patching it afterward, which adds time and material.
Glass options
Low-E coatings, tempered safety glass and obscure glass for bathrooms each change the cost of a unit.
Frame and sill condition
Rotted wood sills or a badly out-of-square opening have to be corrected before a new window can sit properly. We show you what we found before any added work begins.

Window Replacement Questions

Something not covered here? (714) 868-8790

Will you have to cut into my stucco?

Usually not. A retrofit window with a flush fin covers the old aluminum frame and seals to the stucco face. We only recommend cutting back stucco when the old frame is damaged or too far out of square to work with, and we explain that at the estimate.

How long does it take to replace windows in a whole house?

An average-size house is often finished in one day, sometimes two. Full-frame openings take longer than retrofits. We give you a realistic timeline once we have seen each window.

Do I need to be there during the install?

We ask for a few minutes with you at the start of the day to confirm which window goes in which opening, and a few more at the end so you can try every sash and lock yourself. The hours in between are yours. Pulling down blinds and sliding furniture a few feet away from the windows the evening before lets the crew start right away.

What windows do you install?

Most of our replacements use Crystal Pacific vinyl windows, which we are authorized to install. At the estimate, we go over frame colors, glass packages and slider, single-hung or picture configurations.

Can you replace only a few windows instead of the whole house?

Yes. Many people start with the windows that are fogged or hardest to operate. We match the frame color and profile as closely as we can so new and existing windows look consistent from the street, and we tell you honestly which of the rest still have years left.

Get Your Windows Measured Right

We will look at every opening, explain retrofit and full-frame options, and give you a line-item quote. The estimate is free and comes with no pressure. We serve Huntington Beach and nearby towns such as Fountain Valley and Westminster.